Elmo ESD-CC1 Especificações

Multi-function CCTV control keyboard ESD-CC1 Users’ Manual Version 3.0

A. The first three digit (xxx) indicate the step number. B. PST means ‘Preset Point’, it is the preset point used for this step, range f

And then you have to decide the pan direction and the pan speed: 4.2.6 Cruise Under Camera Control Mode, you can press “CRUISE”

Then move the dome to the end point and press “Select Device/ Enter” key to confirm. And then you have to press “Select Device/ Enter” key

4.2.8.2 Zoom speed setting This item allows you to change the speed of zoom lens movement, use "◄"/"►" keys to sel

Menu 2.4.2 is the entry point for parameters related to Alarm1 input: ON/OFF (detect alarm signal or not), NC/NO (alarm signal type) and corres

4.2.8.7 Set TILT bias 4.2.8.8 Check Camera Version This item shows you the hardware and software version of the dome camera, it may be an use

System Setting Mode: 4.3.1 System Linking Menu 1.1 allow you to search for active cameras on the RS485 control bus again, press "◄"

4.3.4 RS-232 Baud rate setting To select Item 4 (as Fig.4.3.4.1) and you can set RS232 Baud rate. The RS-232 protocol of keyboard is the st

4.3.7 System Date/Time Correction Select Item 8(as Fig.4.3.7.1) and hit “ENTER” key (as Fig.4.3.7.2), then you can adjust all the devices at same

4.3.10 Key Press Beep The built-in buzzer will beep when the user press any valid key, this item allow you to turn the beep on or off. Use "◄&

The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the

5. Troubleshooting When you get trouble with using the keyboard, please follow the procedures below to isolate the problem before call back to the

Appendix A. RS485 Communication A.1 Connector (RJ-11 6P6C) Pin No. Definition Direction 1 - - 2 +12V in Power 3 GND Power 4 DA I/O 5 DB I/O 6 -

Appendix B. Technical Specifications The list is the specifications of CCTV control keyboard, our company reserve the right to modify the specifi

Appendix C. The Architecture of SuperMPX and SuperMMX C.1 SuperMPX mode 1 2 3 …….. 16 MPX#1 (ID=224) 1 2 3 …….. 16 MPX#2 (ID=2

C.2 SuperMMX mode 1 2 3 …….. 16 MPX#1 (ID=224) 1 2 3 …….. 16 MPX#2 (ID=225) 1 2 3 …….. 15 MPX#14 (ID=237) 1 2 3 …….. 14 SuperMMX (ID=255) DOME I

Appendix D. Commands Tree of Operating and Setting System + 1 ~ 223 Joystick PAN/TILT control Select Camera Lens Control ZOOM WIDE

SYS Enter password 1. System Linking Scan the exist device System Setup 2. Set Keyboard ID Keyboard ID Setting 0,240-254 3. System Mon

Appendix E. Software upgrade The system installer can use a Personal Computer to download the upgrade software to the keyboard via RS-232 port. T

1478 Old Country Road Plainview, NY 11803 www.elmousa.com

Table Of Contents 1. General Introduction……………………………………………………………………………4 2. Front Panel & Real Panel……………………………………………………………………….5 2.1 Front Pan

1. General Introduction This control keyboard is 100% integrated with our full range CCTV series, or other products that are compatible with the DSC

2. Front Panel & Real Panel 2.1 Front panel 1. Multiplexer mode. 2. Matrix mode.(Reserved) 3. Camera/Dome mode. 4. System Setup key. 5.

2.2 Rear connector panel 1. RS-485 connector (please refer to Appendix A for detail definition). 2. Power jack (12Vdc). 3. RS232 9pin D-sub connect

3. Installation 3.1 RS485 cable Cable Recommendation; Connector: RJ-11 6P6C Cable: Category 5 Max. Length: 1200 Meters (Notice!! Detail Pin Definit

4. Operations 4.1 Power On After connecting all necessary cables, turn on the peripheral devices, and then connect DC12V adapter to the keyboard.

Camera Control Mode: The second row on the LCD allows users to input number 1~255, it’s used to specify preset point or the other camera para